The short answer
Check the Type First
The kind of insulation you have decides whether saving it is possible. Fiberglass batts and blown-in cellulose soak up water like a sponge, lose their thermal value, and often trap mud and contaminants. Rigid foam panels, like EPS or XPS, can sometimes be wiped down, disinfected, and reused if they are not delaminated or deeply contaminated.
Open up the wall or ceiling carefully. Look for sagging, clumping, or a musty smell. If the material feels heavy or shows dark stains, it is likely beyond saving. When in doubt, treat it as unsalvageable and remove it.
- Fiberglass batts: usually replace
- Cellulose: usually replace
- Rigid foam: may save if clean
- Spray foam: often replace
- Mineral wool: may dry but check
- Vapor barriers: replace if torn
Dry the Area Fast
Moisture is the enemy. The longer wet insulation sits, the more likely mold will grow and spread to framing and drywall. You need to start drying within a day or two. Open windows if the outside air is drier than inside, and use fans and dehumidifiers to pull moisture out of the space.
In a humid climate, drying can be slow. Run a dehumidifier continuously and keep air moving. If the insulation is wet but not visibly contaminated, you might try to dry it in place for a short time, but do not wait more than a few days before deciding.
Clean and Disinfect Salvageable Boards
For rigid foam boards that seem intact, remove them and clean both sides with a mild detergent and water. Then apply a disinfectant that is safe for the material. Rinse well and let them dry completely in a well-ventilated area. Do not use bleach on foam, as it can damage the surface.
Check for cracks, soft spots, or water that has seeped between the foam and its facing. If the board has absorbed water into its core, it will not insulate well and should be thrown out. Only keep boards that are firm, dry, and without odor.
Know When to Let the Pros Decide
Sometimes the damage is deeper than you can see. Floodwater can carry sewage, chemicals, or other hazards. If the insulation is in a basement or crawl space that was submerged, the risk is higher. You can remove obvious wet material, but a professional inspection can tell you if hidden moisture is still a problem.
Local water damage pros can test moisture levels in walls and floors. They can also handle removal and disposal safely. If you are unsure, call them before you spend time trying to dry something that will never be safe or effective again.
What to Do After Removal
Once you remove wet insulation, dry the framing and cavities thoroughly. Use fans and dehumidifiers until wood moisture levels are back to normal. Then replace with new insulation that meets current codes. This is not a job to rush, because installing new insulation over damp wood traps moisture and invites mold.
If you have flood insurance, check your policy to see what is covered. Policies vary, and your insurer decides what is covered. Keep receipts and photos of the damaged material. You may also want to ask a pro about vapor barriers and air sealing while the walls are open.
Need help right now?
Water keeps spreading into floors and walls, so it is worth acting early. Calls are answered 24/7.
Call Now (414) 348-0250Frequently asked questions
Can I dry fiberglass insulation in the sun?
Drying fiberglass in the sun rarely works. The material loses its loft and thermal performance once wet, and it can harbor mold spores even after drying. It is usually safer and cheaper to replace it. If you try, dry it completely and check for odors, but expect to throw it out.
How long can wet insulation stay before mold grows?
Mold can start growing within 24 to 48 hours on wet porous surfaces. The longer it sits, the more likely it spreads. You should remove or dry insulation within a day or two. If you cannot dry it fast, remove it to prevent mold from affecting your home's air quality.
Is it safe to reuse rigid foam after a flood?
Rigid foam can be safe to reuse if it is clean, dry, and not contaminated by sewage or chemicals. Wash it with detergent and disinfectant, then dry it fully. If the foam has absorbed water or shows any mold, discard it. When in doubt, replace it to protect your home.